From the brand
AT10II 12 Channel Airplane Transmitter
*Frequently Asked Questions and User Manual’s documents could be found on this page below.
*To works with Drone, you should replace the receiver to mini size R12DSM, R6DSM
*Note: Only binds to Radiolink’s receiver: R12DS, R9DS, R12DSM, R6DS, R6DSM
Radiolink Electronic Co., Ltd. was established in 2003. We are specialized in researching, developing, and producing RC model radio transmitters, flight controllers, receivers, GPS, drones, airplane, and balance charger.
We have a professional R&D team, applied automatic production and testing instrument to provide high-quality, diversified, and competitive technological products to our customers, also including professional after-sales service.
AT10II Radio Key Features
for airplane, helicopter, FPV drone, Tamiya car and more
With DSSS&FHSS protocol, which makes AT10II with excellent anti-interference ability to all 12 channels, long range control up to 2.4 miles (4km). (Actual control distance depends on the flying environment)
- 12 Channels & 15 Models Storage
- Voltage Telemetry Built In (PRM-01)
- Long Range Control Up to 2.4 Miles (4KM)
- Dual/Triple Rate, EXP, EPA, Throttle Cut, Timer etc.
- Wired/Wireless Training, RC Simulator/Crossfire Support
- RSSI, Low Voltage, Fail Safe Alert Setting etc.
- RC Models Selection (Glider, Helicopter, Quad, Airplane Car etc.)
- Dual Sticker Adjustable (Left to Right Throttle and Self-back to Center)
AT10II Key Functions
Real-time Information Telemetry
AT10II works with PRM-03 module and flight controller APM or Pixhawk, Mini PIX, Turbo Pix can give you real-time important information on screen, like battery voltage, speed, altitude, RSSI, flight mode, yaw, roll, pitch and distance and more.
Programmable Mix Control (8 Groups)
Easy to understand graph view, 5-12 channels can be programmed to any advanced setting. An Airbrake can be programmed by using pre-programmed mixes. Multi-servo elevator mixing for Flying Wings or V-Shaped tail models.
Low RSSI, low radio and receiver voltage alarm. with DD sounds and words remind on outdoor readable LCD. Screen background can be change to white for outdoor.
Superb Ergonomically Designed
With 3 of VR switches, 3 of three-way position switches, 4 of two-way position switches, 1 of reset trainer switch. All 12 channels can be customized to any switch.
R12DS 12 Channels Receiver
Support PWM/SBUS signal output, 3-10V support.
Airplane Voltage Telemetry Module
Real-time telemetry airplane voltage monitor on AT10II’s screen when paired with voltage telemetry module PRM-01. Model voltage alarming value can be customized.
7dBi High Gain Antenna
With 7dBi high gain antenna, cuts down interference, that’s ensure control range up to 4KM (2.4 Miles).
Wired/Wireless Training Simulator Support
Support RC simulator wired/wireless training interface feature, AT10II compatible with the majority of aircraft simulator software like Realflight, PhoenixRC, FreeRider.
Voltage Protection System
AT10II with reverse polarity protection circuit, do not worry about it damage even you insert wrong polarity. JST(2pin) connector is easily adapted for various battery layouts.
Support Update Firmware
AT10II radio is easily updated to latest firmware to get new features. Simply connect the transmitter to the PC with a USB cable for updating.
Works with Variety of Receivers
Only compatible with receiver from Radiolink, like R12DS, R9DS, R6DS, R12SM, R6DSM or TBS receiver when works with crossfire module.
Adapts to Most of Types RC Models
Easy to understand user software makes quick work of changing aircraft types models: Fixed Wing, Airplane, Multirotor, Helicopter, Cars and Boats.
|Spread Spectrum Mode||DSSS&FHSS|
|Frequencies Band||2.4GHz ISM (2400MHz – 2483.5MHz)|
|Operating Voltage Range||7.4~15.0V (2S, 3S Lipos, 8*AA are acceptable)|
|Backlight LCD Screen||320×480 Pixel, 3.5 inch outdoor readable LCD|
|Compatible Receiver||Radiolink R12DS, R9DS, R6DS, R12DSM, R6DSM|